Toyota 4Runner: Cellular Phone Inspection

Toyota 4Runner Service Manual / Audio / Visual / Telematics / Audio / Video / Audio And Visual System / Cellular Phone Inspection

PROCEDURE

1.	CHECK USAGE CONDITION

(a) Check that the vehicle and cellular phone meet the following conditions:

NOTICE:

If changing cellular phone settings, updating software, etc. is necessary, make sure to obtain the permission of the customer before performing it.

The cellular phone is "Bluetooth" compatible (Refer to http://www.toyota.com/entune/enside.html).
The cellular phone is registered as a hands-free device.
"Bluetooth" setting of the cellular phone is on.
Operating system and software of the cellular phone are the latest versions.
There are no other radio wave emitting devices ("Wi-Fi" communication device, etc.) in the cabin.

(b) Connect the cellular phone to the in-vehicle device and check that it is connected correctly.

Result	Proceed to
The cellular phone is connected correctly.	A
The cellular phone is not connected correctly.	B

END

2.	RESTART CELLULAR PHONE

(a) Restart the cellular phone.

(b) Turn the ignition switch off.

(d) Connect the cellular phone to the in-vehicle device and check that it is connected correctly.

Result	Proceed to
The cellular phone is connected correctly.	A
The cellular phone is not connected correctly.	B

END

3.	CHECK OPERATION

(a) Check if the in-vehicle device can be recognized by the cellular phone.

Result	Proceed to
In-vehicle device can be recognized.	A
In-vehicle device cannot be recognized.	B

GO TO STEP 5

4.	REGISTER AGAIN

(a) Clear all "Bluetooth" devices registered to the cellular phone and radio and display receiver assembly.

(b) Register the cellular phone again.

Result	Proceed to
The cellular phone is connected correctly.	A
The cellular phone is not connected correctly.	B

END

5.	CHECK USING ANOTHER VEHICLE

(a) Check if the customer's cellular phone functions normally using another "Bluetooth" compatible vehicle.

NOTICE:

Make sure to obtain the customer's permission to perform this procedure.
After the inspection, clear the registered information and usage history acquired during the inspection.

Result	Proceed to
The cellular phone is connected correctly.	A
The cellular phone is not connected correctly.	B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

6.	CHECK USING ANOTHER CELLULAR PHONE

(a) Check if the system functions normally using another "Bluetooth" compatible cellular phone.

NOTICE:

Make sure to obtain the customer's permission to perform this procedure.
After the inspection, clear the registered information and usage history acquired during the inspection.

Result	Proceed to
The cellular phone is connected correctly.	A
The cellular phone is not connected correctly.	B

END (ONLY A "Bluetooth" COMPATIBLE CELLULAR PHONE CAN BE USED)

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

Cellular Phone Registration Failure

PROCEDURE 1. CHECK USAGE CONDITION (a) Check that the vehicle and cellular phone meet the following conditions: NOTICE: If changing cellular phone settings, updatin ...

Sound of Portable Player cannot be Heard from Speakers or Sound is Low

PROCEDURE 1. CHECK PORTABLE PLAYER SETTINGS (a) Check the portable player settings. (1) Check that the volume is not set to "0". (2) Check that the mute i ...

Other materials about Toyota 4Runner:

Front Differential Side Gear Shaft Oil Seal(for 4wd)
Components COMPONENTS ILLUSTRATION Replacement REPLACEMENT CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH and LH sides. The procedure listed below is for the LH side. PROCEDURE 1. REMOVE FRONT DRIVE SHAFT ASSEM ...

Ultrasonic Sensor(for Front)
Components COMPONENTS ILLUSTRATION ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE UPPER RADIATOR SUPPORT SEAL 2. REMOVE FRONT BUMPER COVER 3. REMOVE NO. 2 ENGINE ROOM WIRE 4. REMOVE NO. 1 ULTRASONIC SENSOR (a) Detach th ...

0.0267