Toyota 4Runner: Data List / Active Test
DATA LIST / ACTIVE TEST
1. READ DATA LIST
HINT:
Using the Techstream to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / (desired system) / Data List.
(e) According to the display on the Techstream, read the Data List.
Master Switch|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
D Door P/W Auto SW |
Driver side power window auto up/down signal / ON or OFF |
ON: Driver side power window auto up/down switch on power window regulator master switch operated OFF: Driver side power window switch on power window regulator master switch not operated |
- |
|
P Door P/W Auto SW |
Front passenger side power window remote auto up/down signal / ON or OFF |
ON: Front passenger side power window remote auto up/down switch on power window regulator master switch operated OFF: Front passenger side power window switch on power window regulator master switch not operated |
- |
|
RR Door P/W Auto SW |
Rear power window RH remote auto up/down signal / ON or OFF |
ON: Rear power window RH remote auto up/down switch on power window regulator master switch operated OFF: Rear power window switch RH on power window regulator master switch not operated |
- |
|
RL Door P/W Auto SW |
Rear power window LH remote auto up/down signal / ON or OFF |
ON: Rear power window LH remote auto up/down switch on power window regulator master switch operated OFF: Rear power window switch LH on power window regulator master switch not operated |
- |
|
P Door P/W Up SW |
Front passenger side power window remote manual up signal / ON or OFF |
ON: Front passenger side power window remote manual up switch on power window regulator master switch operated OFF: Front passenger side power window switch on power window regulator master switch not operated |
- |
|
RR Door P/W up switch |
Rear power window RH remote manual up signal / ON or OFF |
ON: Rear power window RH remote manual up switch on power window regulator master switch operated OFF: Rear power window switch RH on power window regulator master switch not operated |
- |
|
RL Door P/W up switch |
Rear power window LH remote manual up signal / ON or OFF |
ON: Rear power window LH remote manual up switch on power window regulator master switch operated OFF: Rear power window switch LH on power window regulator master switch not operated |
- |
|
P Door P/W Down SW |
Front passenger side power window remote manual down signal / ON or OFF |
ON: Front passenger side power window remote manual down switch on power window regulator master switch operated OFF: Front passenger side power window switch on power window regulator master switch not operated |
- |
|
RR Door P/W Down SW |
Rear power window RH remote manual down signal / ON or OFF |
ON: Rear power window RH remote manual down switch on power window regulator master switch operated OFF: Rear power window switch RH on power window regulator master switch not operated |
- |
|
RL Door P/W Down SW |
Rear power window LH remote manual down signal / ON or OFF |
ON: Rear power window LH remote manual down switch on power window regulator master switch operated OFF: Rear power window switch LH on power window regulator master switch not operated |
- |
|
Window Lock Switch Status |
Power window lock switch / ON or OFF |
ON: Power window lock switch on OFF: Power window lock switch off |
- |
|
Number of Trouble Codes |
Number of trouble codes / Min.: 0, Max.: 255 |
Number of DTCs stored |
- |
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
D Door P/W Auto SW |
Driver side power window auto up/down signal / ON or OFF |
ON: Driver side power window auto up/down switch operated OFF: Driver side power window switch not operated |
- |
|
D Door P/W Up SW |
Driver side power window manual up signal / ON or OFF |
ON: Driver side power window manual up switch operated OFF: Driver side power window switch not operated |
- |
|
D Door P/W Down SW |
Driver side power window manual down signal / ON or OFF |
ON: Driver side power window manual down switch operated OFF: Driver side power window switch not operated |
- |
|
Glass Position (Close-1/4) |
Jam protection status of window glass within range of fully closed to 1/4 open position / OK or Caution |
OK: Motor operates normally between fully closed and 1/4 open positions Caution: Jam protection function operating due to detection of foreign object or irregular movement |
- |
|
Glass Position (1/4-2/4) |
Jam protection status of window glass within range of 1/4 open to 1/2 open position / OK or Caution |
OK: Motor operates normally between 1/4 open and 1/2 open positions Caution: Jam protection function operating due to detection of foreign object or irregular movement |
- |
|
Glass Position (2/4-3/4) |
Jam protection status of window glass within range of 1/2 open to 3/4 open position / OK or Caution |
OK: Motor operates normally between 1/2 open and 3/4 open positions Caution: Jam protection function operating due to detection of foreign object or irregular movement |
- |
|
Glass Position (3/4-Open) |
Jam protection status of window glass within range of 3/4 open to fully open position / OK or Caution |
OK: Motor operates normally between 3/4 open and fully open positions Caution: Jam protection function operating due to detection of foreign object or irregular movement |
- |
|
D Window Auto Up |
Auto up operation using the multiplex network master switch assembly / ON or OFF |
Customize setting displayed |
- |
|
D Window Auto Down |
Auto down operation using the multiplex network master switch assembly / ON or OFF |
Customize setting displayed |
- |
|
Number of Trouble Codes |
Number of trouble codes / Min.: 0, Max.: 255 |
Number of DTCs stored |
- |
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
P Door P/W Auto SW |
Front passenger side power window auto up/down signal / ON or OFF |
ON: Front passenger side power window auto up/down switch operated OFF: Front passenger side power window regulator switch not operated |
- |
|
P Door P/W Up SW |
Front passenger side power window manual up signal / ON or OFF |
ON: Front passenger side power window manual up switch operated OFF: Front passenger side power window regulator switch not operated |
- |
|
P Door P/W Down SW |
Front passenger side power window manual down signal / ON or OFF |
ON: Front passenger side power window manual down switch operated OFF: Front passenger side power window regulator switch not operated |
- |
|
Glass Position (Close-1/4) |
Jam protection status of window glass within range of fully closed to 1/4 open position / OK or Caution |
OK: Motor operates normally between fully closed and 1/4 open positions Caution: Jam protection function operating due to detection of foreign object or irregular movement |
- |
|
Glass Position (1/4-2/4) |
Jam protection status of window glass within range of 1/4 open to 1/2 open position / OK or Caution |
OK: Motor operates normally between 1/4 open and 1/2 open positions Caution: Jam protection function operating due to detection of foreign object or irregular movement |
- |
|
Glass Position (2/4-3/4) |
Jam protection status of window glass within range of 1/2 open to 3/4 open position / OK or Caution |
OK: Motor operates normally between 1/2 open and 3/4 open positions Caution: Jam protection function operating due to detection of foreign object or irregular movement |
- |
|
Glass Position (3/4-Open) |
Jam protection status of window glass within range of 3/4 open to fully open position / OK or Caution |
OK: Motor operates normally between 3/4 open and fully open positions Caution: Jam protection function operating due to detection of foreign object or irregular movement |
- |
|
P Window Auto Up |
Auto up operation using the power window regulator switch assembly / ON or OFF |
Customize setting displayed |
- |
|
P Window Auto Up From Driver |
Remote auto up operation using the multiplex network master switch assembly / ON or OFF |
Customize setting displayed |
- |
|
P Window Auto Down |
Auto down operation using the power window regulator switch assembly / ON or OFF |
Customize setting displayed |
- |
|
P Window Auto Down From Driver |
Remote auto down operation using the multiplex network master switch assembly / ON or OFF |
Customize setting displayed |
- |
|
Number of Trouble Codes |
Number of trouble codes / Min.: 0, Max.: 255 |
Number of DTCs stored |
- |
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
RL Door P/W Auto SW |
Rear power window LH auto up/down signal / ON or OFF |
ON: Rear power window LH auto up/down switch operated OFF: Rear power window LH switch not operated |
- |
|
RL Door P/W Up SW |
Rear power window LH manual up signal / ON or OFF |
ON: Rear power window LH manual up switch operated OFF: Rear power window LH switch not operated |
- |
|
RL Door P/W Down SW |
Rear power window LH manual down signal / ON or OFF |
ON: Rear power window LH manual down switch operated OFF: Rear power window LH switch not operated |
- |
|
Glass Position (Close-1/4) |
Jam protection status of window glass within range of fully closed to 1/4 open position / OK or Caution |
OK: Motor operates normally between fully closed and 1/4 open positions Caution: Jam protection function operating due to detection of foreign object or irregular movement |
- |
|
Glass Position (1/4-2/4) |
Jam protection status of window glass within range of 1/4 open to 1/2 open position / OK or Caution |
OK: Motor operates normally between 1/4 open and 1/2 open positions Caution: Jam protection function operating due to detection of foreign object or irregular movement |
- |
|
Glass Position (2/4-3/4) |
Jam protection status of window glass within range of 1/2 open to 3/4 open position / OK or Caution |
OK: Motor operates normally between 1/2 open and 3/4 open positions Caution: Jam protection function operating due to detection of foreign object or irregular movement |
- |
|
Glass Position (3/4-Open) |
Jam protection status of window glass within range of 3/4 open to fully open position / OK or Caution |
OK: Motor operates normally between 3/4 open and fully open positions Caution: Jam protection function operating due to detection of foreign object or irregular movement |
- |
|
RL Window Auto Up |
Auto up operation using the power window regulator switch assembly / ON or OFF |
Customize setting displayed |
- |
|
RL Window Auto Up From Driver |
Remote auto up operation using the multiplex network master switch assembly / ON or OFF |
Customize setting displayed |
- |
|
RL Window Auto Down |
Auto down operation using the power window regulator switch assembly / ON or OFF |
Customize setting displayed |
- |
|
RL Window Auto Down From Driver |
Remote auto down operation using the multiplex network master switch assembly / ON or OFF |
Customize setting displayed |
- |
|
Number of Trouble Codes |
Number of trouble codes / Min.: 0, Max.: 255 |
Number of DTCs stored |
- |
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
RR Door P/W Auto SW |
Rear power window RH auto up/down signal / ON or OFF |
ON: Rear power window RH auto up/down switch operated OFF: Rear power window RH switch not operated |
- |
|
RR Door P/W Up SW |
Rear power window RH manual up signal / ON or OFF |
ON: Rear power window RH manual up switch operated OFF: Rear power window RH switch not operated |
- |
|
RR Door P/W Down SW |
Rear power window RH manual down signal / ON or OFF |
ON: Rear power window RH manual down switch operated OFF: Rear power window RH switch not operated |
- |
|
Glass Position (Close-1/4) |
Jam protection status of window glass within range of fully closed to 1/4 open position / OK or Caution |
OK: Motor operates normally between fully closed and 1/4 open positions Caution: Jam protection function operating due to detection of foreign object or irregular movement |
- |
|
Glass Position (1/4-2/4) |
Jam protection status of window glass within range of 1/4 open to 1/2 open position / OK or Caution |
OK: Motor operates normally between 1/4 open and 1/2 open positions Caution: Jam protection function operating due to detection of foreign object or irregular movement |
- |
|
Glass Position (2/4-3/4) |
Jam protection status of window glass within range of 1/2 open to 3/4 open position / OK or Caution |
OK: Motor operates normally between 1/2 open and 3/4 open positions Caution: Jam protection function operating due to detection of foreign object or irregular movement |
- |
|
Glass Position (3/4-Open) |
Jam protection status of window glass within range of 3/4 open to fully open position / OK or Caution |
OK: Motor operates normally between 3/4 opens fully open and positions Caution: Jam protection function operating due to detection of foreign object or irregular movement |
- |
|
RR Window Auto Up |
Auto up operation using the power window regulator switch assembly / ON or OFF |
Customize setting displayed |
- |
|
RR Window Auto Up From Driver |
Remote auto up operation using the multiplex network master switch assembly / ON or OFF |
Customize setting displayed |
- |
|
RR Window Auto Down |
Auto down operation using the power window regulator switch assembly / ON or OFF |
Customize setting displayed |
- |
|
RR Window Auto Down From Driver |
Remote auto down operation using the multiplex network master switch assembly / ON or OFF |
Customize setting displayed |
- |
|
Number of Trouble Codes |
Number of trouble codes / Min.: 0, Max.: 255 |
Number of DTCs stored |
- |
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
Door Key SW-Lock |
Front door lock/unlock switch LH lock signal (key-linked lock switch) / ON or OFF |
ON: Front door LH key cylinder turned to lock position OFF: Front door LH key cylinder turned to unlock position |
- |
|
Door Key SW-Unlock |
Front door lock/unlock switch LH unlock signal (key-linked unlock switch) / ON or OFF |
ON: Front door LH key cylinder turned to unlock position OFF: Front door LH key cylinder turned to lock position |
- |
|
FL Door Courtesy SW |
Front door courtesy light switch LH signal / ON or OFF |
ON: Front door LH closed OFF: Front door LH open |
- |
|
FR Door Courtesy SW |
Front door courtesy light switch RH signal / ON or OFF |
ON: Front door RH closed OFF: Front door RH open |
- |
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
Key Switch Operation Locked |
Tail gate control switch signal / ON or OFF |
ON: Back door key cylinder turned to lock position OFF: Back door key cylinder not turned |
- |
|
Key Switch Operation Unlocked |
Tail gate control switch signal / ON or OFF |
ON: Back door key cylinder turned to unlock position OFF: Back door key cylinder not turned |
- |
|
Wiper Retracted Position |
Rear wiper retracting switch signal / ON or OFF |
ON: Rear wiper in retracted position OFF: Rear wiper in other position |
- |
|
Wiper Reverse Position |
Rear wiper reverse position switch signal / ON or OFF |
ON: Rear wiper in reverse position OFF: Rear wiper in other position |
- |
|
Back Door Courtesy Switch |
Back door courtesy light switch signal / ON or OFF |
ON: Back door open OFF: Back door closed |
- |
|
Inside Back Door P/W Up SW |
Back door power window regulator switch manual up signal / ON or OFF |
ON: Back door power window regulator manual up switch operated OFF: Back door power window regulator switch not operated |
- |
|
Inside Back Door P/W Down SW |
Back door power window regulator switch manual down signal / ON or OFF |
ON: Back door power window regulator manual down switch operated OFF: Back door power window regulator switch not operated |
- |
|
Inside Back Door P/W Auto SW |
Back door power window regulator switch auto up/down signal / ON or OFF |
ON: Back door power window regulator auto up/down switch operated OFF: Back door power window regulator switch not operated |
- |
|
Outside Back Door P/W Up SW |
Back door control switch lock signal / ON or OFF |
ON: LOCK switch of back door control switch operated OFF: LOCK switch of back door control switch not operated |
- |
|
Outside Back Door P/W Down SW |
Back door control switch unlock signal / ON or OFF |
ON: UNLOCK switch of back door control switch operated OFF: UNLOCK switch of back door control switch not operated |
- |
|
Back Door P/W Status |
Back door power window position / Open or Close |
Open: Back door window open Close: Back door window closed |
- |
|
Smart Back Door P/W Control |
Smart back door power window signal / ON or OFF |
ON: LOCK or UNLOCK switch of back door control switch operated OFF: LOCK and UNLOCK switches of back door control switch not operated |
- |
|
Smart Back Door P/W Position |
Back door power window position / Unfixed, Open, Close or Others |
Unfixed: Back door window operating Open: Back door window open Close: Back door window fully closed Others: Condition other than Unfixed, Open or Close |
- |
|
Number of Trouble Codes |
Number of trouble codes / Min.: 0, Max.: 255 |
Number of DTCs stored |
- |
2. PERFORM ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / (desired system) / Active Test.
(e) According to the display on the Techstream, perform the Active Test.
CAUTION:
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.
D-Door Motor|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Power Window |
Driver side power window |
OFF/UP/DOWN |
- |
|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Power Window |
Passenger side power window |
OFF/UP/DOWN |
- |
|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Power Window |
Rear LH side power window |
OFF/UP/DOWN |
- |
|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Power Window |
Rear RH side power window |
OFF/UP/DOWN |
- |
|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
IG OFF P/W Control Permission Output |
Front door power window |
OFF/ON |
- |
|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Back Door Power Window |
Back door power window |
OFF/UP/DOWN |
- |
Dtc Check / Clear
DTC CHECK / CLEAR
1. CHECK DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / (desired sy ...
Fail-safe Chart
FAIL-SAFE CHART
1. POWER WINDOW OPERATION IN FAIL-SAFE MODE
HINT:
If the pulse sensor built into a power window regulator motor malfunctions, the
power window control system enters fail-safe mode ...
Other materials about Toyota 4Runner:
Menu list of the hands-free phone system
Normal operation
Using a short cut key
Automatic volume adjustment
When vehicle speed reaches 50 mph (80 km/h) or more, the volume automatically
increases. The volume returns to the previous volume setting when vehicle speed
drops to 43 mph (70 k ...
Illumination for Panel Switch does not Come on with Tail Switch ON
CAUTION / NOTICE / HINT
NOTICE:
After replacing the navigation receiver assembly of vehicles subscribed to pay-type
satellite radio broadcasts, registration of the XM radio ID is necessary.
PROCEDURE
1.
CHECK VEHICLE SIGNAL (OPERAT ...
0.0144