Toyota 4Runner manuals

Toyota 4Runner: Data List / Active Test

DATA LIST / ACTIVE TEST

1. DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Warm up the engine.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn on the Techstream.

(e) Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

(f) According to the display on the Techstream, read the Data List.

ABS/VSC/TRAC

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

ABS Warning Light

ABS warning light/ ON or OFF

OFF

-

Brake Warning Light

Brake warning light/ ON or OFF

OFF

-

Downhill Assist Control Light

Downhill assist control indicator light/ ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

Buzzer

Buzzer/ ON or OFF

ON: Buzzer on

OFF: Buzzer off

The combination meter has a built-in buzzer.

Stop Light SW

Stop light switch/ ON or OFF

ON: Brake pedal depressed

OFF: Brake pedal released

-

Parking Brake SW

Parking brake switch/ ON or OFF

ON: Parking brake applied

OFF: Parking brake released

-

Reservoir Warning SW

Brake fluid level warning switch/ ON or OFF

OFF

-

Main Idle SW

Main idle switch/ ON or OFF

ON: Accelerator pedal released

OFF: Accelerator pedal depressed

-

Gear Position

Gear position/ Fail, 1st-8th, P,N, R, Not R

Actual gear position

-

Shift Lever Position

Shift lever position/ Fail, 1st-6th/B, D/M, P,N, R

Actual shift lever position

-

Shift Information

Shift information/ ON or OFF

ON: During gear change

OFF: Not during gear change

-

Inspection Mode

Inspection mode/ Other or Inspect

Other: Normal mode

Inspect: Inspection mode

-

Number of IG ON (Inspection)

Number of times ignition switch turned to ON after entering inspection mode/ Min.: 0, Max.: 255

-

-

Downhill Assist Control SW

Downhill assist control switch/ ON or OFF

ON: Downhill assist control on

OFF: Downhill assist control off

-

Master Cylinder Sensor

Master cylinder pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V

When brake pedal released: 0.3 to 0.9 V

The valve increases when the brake pedal is depressed.

Zero Point of M/C

Memorized zero value/ Min.: -12.50 MPa, Max.: 12.40 MPa

-

-

Accumulator Sensor

Accumulator pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V

3.58 to 5 V

If the value is constant regardless of the pump operation, an accumulator pressure sensor malfunction is suspected.

Deceleration Sensor

Deceleration sensor reading/ Min.: -18.327 m/s2, Max.: 18.183 m/s2

-

Changes continuously during acceleration/deceleration.

Zero Point of Decele

Memorized zero value/ Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

-

Deceleration Sensor2

Deceleration sensor 2 reading/ Min.: -18.327 m/s2, Max.: 18.183 m/s2

-

Changes continuously during acceleration/deceleration.

Zero Point of Decele2

Memorized zero value/ Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

-

Yaw Rate Sensor

Yaw rate and acceleration sensor 1/ Min.: -128°/s, Max.: 127°/s

Vehicle stationary: 0°/s

Right turn: -128 to 0°/s

Left turn: 0 to 127°/s

-

Zero Point of Yaw Rate

Memorized zero value/ Min.: -128°/s, Max.: 127°/s

-

-

Steering Angle Sensor

Steering angle sensor/ Min.: -3276.8°, Max.: 3276.7°

Left turn: Increases

Right turn: Decreases

-

Zero Point of Steering Angle

Memorized zero value/ Min.: -3276.8°, Max.: 3276.7°

-

-

Lateral G

Lateral G/ Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

Changes in proportion with acceleration during turning.

Forward and Rearward G

Forward and rearward G/ Min.: -25.10 m/s2, Max.: 24.90 m/s2

-

Changes in proportion with acceleration during acceleration/deceleration.

Yaw Rate Value

Yaw rate value/ Min.: -128°/s, Max.: 127°/s

-

Changes in proportion with yaw during turning.

Steering Angle Value

Steering angle value/ Min.: -3276.8°, Max.: 3276.7°

-

Changes in proportion with the amount of steering wheel rotation during steering operation.

Stop Light Relay

Stop light control relay (Stop Light switch assembly)/ ON or OFF

ON: Relay on

OFF: Relay off

-

Crawl Control Light

Crawl indicator light/ ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

Slip Indicator Light

Slip indicator light/ ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

Rear Diff Lock Switch

Rear differential lock detection switch/ ON or OFF

ON: Rear differential lock detection switch on

OFF: Rear differential lock detection switch off

-

Automatic Disconnect Diff SW*2

A.D.D. actuator 4WD detection switch/ ON or OFF

ON: 4WD

OFF: 2WD

-

L4 Switch

Transfer L4 detection switch/ ON or OFF

ON: L4

OFF: except L4

-

FR Wheel Speed

Front wheel speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)

Actual wheel speed

No large fluctuations when driving at a constant speed.

FL Wheel Speed

Front wheel speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)

Actual wheel speed

No large fluctuations when driving at a constant speed.

RR Wheel Speed

Rear wheel speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)

Actual wheel speed

No large fluctuations when driving at a constant speed.

RL Wheel Speed

Rear wheel speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)

Actual wheel speed

No large fluctuations when driving at a constant speed.

Vehicle Speed

Maximum wheel speed sensor reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)

Actual vehicle speed

No large fluctuations when driving at a constant speed.

FR Wheel Acceleration

Front wheel acceleration RH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

Changes continuously during acceleration/deceleration.

FL Wheel Acceleration

Front wheel acceleration LH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

Changes continuously during acceleration/deceleration.

RR Wheel Acceleration

Rear wheel acceleration RH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

Changes continuously during acceleration/deceleration.

RL Wheel Acceleration

Rear wheel acceleration LH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2

-

Changes continuously during acceleration/deceleration.

FR Wheel Direction

Front wheel direction RH/ Forward or Back

Forward: Forward

Back: Back

-

FL Wheel Direction

Front wheel direction LH/ Forward or Back

Forward: Forward

Back: Back

-

RR Wheel Direction

Rear wheel direction RH/ Forward or Back

Forward: Forward

Back: Back

-

RL Wheel Direction

Rear wheel direction LH/ Forward or Back

Forward: Forward

Back: Back

-

Stop Light Relay Output

Stop light control relay (Stop Light switch assembly) output/ ON or OFF

ON: Relay on (Stop light on)

OFF: Relay off (Stop light off)

-

Crawl Control Switch

Crawl speed selector switch status/ LOW, MIDLOW, MID, MIDHIGH or HIGH

Actual crawl speed selector switch position

-

Auto LSD Indicator Light*1

Auto LSD indicator light/ ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

A-TRAC Indicator Light

A-TRAC indicator light/ ON or OFF

ON: Indicator light on

OFF: Indicator light off

-

FR Wheel ABS Ctrl Status

Front wheel RH ABS control status/ ON or OFF

ON: During control

OFF: Not during control

-

FL Wheel ABS Ctrl Status

Front wheel LH ABS control status/ ON or OFF

ON: During control

OFF: Not during control

-

RR Wheel ABS Ctrl Status

Rear wheel RH ABS control status/ ON or OFF

ON: During control

OFF: Not during control

-

RL Wheel ABS Ctrl Status

Rear wheel LH ABS control status/ ON or OFF

ON: During control

OFF: Not during control

-

RR Wheel EBD Ctrl Status

Rear wheel RH EBD control status/ ON or OFF

ON: During control

OFF: Not during control

-

RL Wheel EBD Ctrl Status

Rear wheel LH EBD control status/ ON or OFF

ON: During control

OFF: Not during control

-

BA Ctrl Status

BA control status/ ON or OFF

ON: During control

OFF: Not during control

-

TRC (TRAC) Ctrl Status

Traction control status/ ON or OFF

ON: During control

OFF: Not during control

-

TRC (TRAC) Engine Ctrl Status

Traction control (engine control) status/ ON or OFF

ON: During control

OFF: Not during control

-

TRC (TRAC) Brake Ctrl Status

Traction control (brake control) status/ ON or OFF

ON: During control

OFF: Not during control

-

FR Wheel VSC Ctrl Status

Front wheel RH VSC control status/ ON or OFF

ON: During control

OFF: Not during control

-

FL Wheel VSC Ctrl Status

Front wheel LH VSC control status/ ON or OFF

ON: During control

OFF: Not during control

-

RR Wheel VSC Ctrl Status

Rear wheel RH VSC control status/ ON or OFF

ON: During control

OFF: Not during control

-

RL Wheel VSC Ctrl Status

Rear wheel LH VSC control status/ ON or OFF

ON: During control

OFF: Not during control

-

Engine Revolutions

Engine speed/ Min.: 0 rpm, Max.: 65535 rpm

Actual engine speed

-

Real Engine Torque

Actual engine torque/ Min.: -1024.0 Nm, Max.: 1023.0 Nm

-

-

Accelerator Opening Angle %

Percentage of accelerator pedal opening angle/ Min.: 0.0%, Max.: 128.0%

When accelerator pedal released: 0%

Changes in proportion with the movement of the pedal during accelerator pedal operation.

Solenoid Relay

Solenoid relay/ ON or OFF

ON: Solenoid relay on

OFF: Solenoid relay off

-

Motor Relay

Motor relay/ ON or OFF

ON: Motor relay on

OFF: Motor relay off

-

TR(A)C/VSC Solenoid (SRM2)

TRAC/VSC solenoid (SRM2)/ ON or OFF

ON: Operating

OFF: Not operating

-

TR(A)C/VSC Solenoid (SRM1)

TRAC/VSC solenoid (SRM1)/ ON or OFF

ON: Operating

OFF: Not operating

-

TR(A)C/VSC Solenoid (SRC2)

TRAC/VSC solenoid (SRC2)/ ON or OFF

ON: Operating

OFF: Not operating

-

TR(A)C/VSC Solenoid (SRC1)

TRAC/VSC solenoid (SRC1)/ ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SFRH)

ABS solenoid (SFRH)/ ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SFRR)

ABS solenoid (SFRR)/ ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SFLH)

ABS solenoid (SFLH)/ ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SFLR)

ABS solenoid (SFLR)/ ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SRRH)

ABS solenoid (SRRH)/ ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SRRR)

ABS solenoid (SRRR)/ ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SRLH)

ABS solenoid (SRLH)/ ON or OFF

ON: Operating

OFF: Not operating

-

ABS Solenoid (SRLR)

ABS solenoid (SRLR)/ ON or OFF

ON: Operating

OFF: Not operating

-

FR Speed Open

Front speed sensor RH open circuit detection/ Error or Normal

Normal

-

FL Speed Open

Front speed sensor LH open circuit detection/ Error or Normal

Normal

-

RR Speed Open

Rear speed sensor RH open circuit detection/ Error or Normal

Normal

-

RL Speed Open

Rear speed sensor LH open circuit detection/ Error or Normal

Normal

-

EFI Communication Open

ECM communication open circuit detection/ Error or Normal

Normal

-

Yaw Rate Open

Yaw rate and acceleration sensor open circuit detection/ Error or Normal

Normal

-

Deceleration Open

Deceleration sensor open circuit detection/ Error or Normal

Normal

-

Steering Open

Steering angle sensor open circuit detection/ Error or Normal

Normal

-

Master Cylinder Open

Master cylinder pressure sensor open circuit detection/ Error or Normal

Normal

-

IG1 Voltage Value

IG1 voltage value/ Min.: 0.00 V, Max.: 20.00 V

Ignition switch ON: 11 to 14 V

-

IG2 Voltage Value

IG2 voltage value/ Min.: 0.00 V, Max.: 20.00 V

Ignition switch ON: 11 to 14 V

-

TRAC/VSC Off Mode

TRAC/VSC off mode/ Normal, TRC OFF, Unknown or VSC OFF

Normal: Normal

TRC OFF: TRAC OFF mode

VSC OFF: VSC OFF mode

-

Number of DTC

Number of DTCs/ Min.: 0, Max.: 255

0

-

IG Voltage Value Decreased

IG1 voltage value decreased/ Error or Normal

Normal

-

IG Voltage Value Increased

IG1 voltage value increased/ Error or Normal

Normal

-

FR Speed Sensor Voltage Open

Front speed sensor RH voltage open circuit detection/ Error or Normal

Normal

-

FL Speed Sensor Voltage Open

Front speed sensor LH voltage open circuit detection/ Error or Normal

Normal

-

RR Speed Sensor Voltage Open

Rear speed sensor RH voltage open circuit detection/ Error or Normal

Normal

-

RL Speed Sensor Voltage Open

Rear speed sensor LH voltage open circuit detection/ Error or Normal

Normal

-

M/C Pressure Sensor Noise

Master cylinder pressure sensor noise detection/ Error or Normal

Normal

-

Yaw Rate Sensor Voltage Open

Yaw rate and acceleration sensor voltage open circuit detection/ Error or Normal

Normal

-

EFI Communication Invalid

ECM communication invalid detection/ Error or Normal

Normal

-

  • *1: for 2WD
  • *2: for Part-time 4WD

2. ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Warm up the engine.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn on the Techstream.

(e) Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.

(f) According to the display on the Techstream, perform the Active Test.

ABS/VSC/TRAC

Tester Display

Test Part

Control Range

Diagnostic Note

ABS Warning Light

ABS warning light

Warning light ON/OFF

Observe the combination meter.

Brake Warning Light

BRAKE warning light

Warning light ON/OFF

Observe the combination meter.

Downhill Assist Control Light

Downhill assist control indicator light

Indicator light ON/OFF

Observe the combination meter.

Solenoid Relay

Solenoid relay

Relay ON/OFF

An operating sound of the solenoid (clicking sound) can be heard.

Motor Relay

Motor relay

Relay ON/OFF

An operating sound of the motor can be heard.

Stop Light Relay

Stop light control relay (Stop Light switch assembly)

Relay ON/OFF

Observe the stop light (does not come on for 2 to 5 seconds).

ABS Solenoid (SRLR)

ABS solenoid (SRLR)

Solenoid ON/OFF

An operating sound of the solenoid (clicking sound) can be heard.

ABS Solenoid (SRLH)

ABS solenoid (SRLH)

Solenoid ON/OFF

An operating sound of the solenoid (clicking sound) can be heard.

ABS Solenoid (SRRR)

ABS solenoid (SRRR)

Solenoid ON/OFF

An operating sound of the solenoid (clicking sound) can be heard.

ABS Solenoid (SRRH)

ABS solenoid (SRRH)

Solenoid ON/OFF

An operating sound of the solenoid (clicking sound) can be heard.

ABS Solenoid (SFLR)

ABS solenoid (SFLR)

Solenoid ON/OFF

An operating sound of the solenoid (clicking sound) can be heard.

ABS Solenoid (SFLH)

ABS solenoid (SFLH)

Solenoid ON/OFF

An operating sound of the solenoid (clicking sound) can be heard.

ABS Solenoid (SFRR)

ABS solenoid (SFRR)

Solenoid ON/OFF

An operating sound of the solenoid (clicking sound) can be heard.

ABS Solenoid (SFRH)

ABS solenoid (SFRH)

Solenoid ON/OFF

An operating sound of the solenoid (clicking sound) can be heard.

VSC/TRAC Solenoid (SRMR)

VSC/TRAC solenoid (SRM2)

Solenoid ON/OFF

An operating sound of the solenoid (clicking sound) can be heard.

VSC/TRAC Solenoid (SRMF)

VSC/TRAC solenoid (SRM1)

Solenoid ON/OFF

An operating sound of the solenoid (clicking sound) can be heard.

VSC/TRAC Solenoid (SRCR)

VSC/TRAC solenoid (SRC2)

Solenoid ON/OFF

An operating sound of the solenoid (clicking sound) can be heard.

VSC/TRAC Solenoid (SRCF)

VSC/TRAC solenoid (SRC1)

Solenoid ON/OFF

An operating sound of the solenoid (clicking sound) can be heard.

ABS Solenoid

Selection of multiple holding solenoids (SFRH, SFLH, SRRH and SRLH) and pressure reduction solenoids (SFRR, SFLR, SRRR and SRLR) possible

Start/Stop

-

VSC/TRAC Solenoid

Selection of multiple VSC/TRAC solenoids [SRMR (SRM1), SRMF (SRM1), SRCR (SRC2) and SRCF (SRC1)] possible

Start/Stop

-

Crawl Control Light

Crawl indicator light

Indicator light ON/OFF

Observe the combination meter.

TRAC OFF Indicator Light

TRAC OFF indicator light

Indicator light ON/OFF

Observe the combination meter.

VSC OFF Indicator Light

VSC OFF indicator light

Indicator light ON/OFF

Observe the combination meter.

Slip Indicator Light

Slip indicator light

Indicator light ON/OFF

Observe the combination meter.

Auto LSD Indicator Light

Auto LSD indicator light

Indicator light ON/OFF

Observe the combination meter.

Freeze Frame Data
FREEZE FRAME DATA 1. FREEZE FRAME DATA (a) Whenever a DTC is stored, the skid control ECU stores the current vehicle (sensor) state as freeze frame data. (b) The skid control ECU stores the numbe ...

Fail-safe Chart
FAIL-SAFE CHART 1. FAIL-SAFE OPERATION If there is a problem with sensor signals or hydraulic brake booster systems, the skid control ECU prohibits power from being supplied to the hy ...

Other materials about Toyota 4Runner:

Park / Neutral Position Switch Circuit
DESCRIPTION This circuit sends the park/neutral position switch assembly signals to the clearance warning ECU assembly. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to this system before performing the followin ...

Reassembly
REASSEMBLY CAUTION / NOTICE / HINT PROCEDURE 1. INSTALL PLUG (a) Using the SST and a hammer, install a new plug. SST: 09950-60010 09951-00450 SST: 09950-70010 09951-07100 2. INSTALL FRO ...

© 2016-2024 | www.to4runner.net

0.0082